Hand-held-products Dolphin 7200 User Manual Page 70
- Page / 114
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
9 - 8 Dolphin® 7200 User’s Guide
Setting Up for Communications
The Dolphin terminal and Dolphin Compact HomeBase support RS-232 communications through the RS-232 Main
Communications Port on the back of the Dolphin 7200 Compact HomeBase. The HomeBase translates the RS-232 signals from
the host computer into infrared signals to communicate with the Dolphin terminal.
The HomeBase RS-232 interface allows the Dolphin terminal to communicate to a personal computer, modem, or any standard
RS-232 device using a standard serial cable and communications software.
Follow these steps to set up the Dolphin HomeBase and Dolphin terminal for communications:
1. Set up the Dolphin Compact HomeBase.
2. Set-up the Dolphin terminal.
3. Follow the data transfer sequence as described by your application.
Setting up the Dolphin Compact HomeBase
Set the Dolphin Compact HomeBase on any dry, stable surface such as a desktop. Before mounting the Compact HomeBase,
check to ensure that all AC wall transformers have a nearby electrical outlet. Be sure to provide enough workspace with good
lighting for the user to view and operate the Dolphin terminal while it is in the HomeBase.
Connecting the Cables
Connect the Compact HomeBase to the host computer or other device by plugging an RS-232 serial cable into the RS-232
Communications Port on the rear of the HomeBase. The wiring of your cable depends on whether the other device is set up as
a Data Communications Equipment (DCE) or Data Terminal Equipment (DTE) device.
The HomeBase RS-232 Port is configured as a DCE device. To communicate with a DTE device such as a computer, use a
standard (or straight-through) RS-232 cable. To communicate with a DCE device, use either a null modem adapter in line with a
standard RS-232 cable, or a null-modem serial cable.
You can make your own cables by following the pin configuration in the chart below. To do so, you must determine if your host
RS-232 device is 9-pin or 25-pin, and whether it is configured as a DCE or DTE device.
With the Dolphin 7200 Compact HomeBase, connect each device to the RS-232 Communications Port on the back of the
HomeBase. The Compact HomeBase cannot be networked.
Connect the power supply to the Compact HomeBase. Plug the AC transformer into the Dolphin HomeBase 12 Volt DC power
supply connector. The AC wall transformer provided can power only one Dolphin Compact HomeBase.
Hand Held Products recommends that you leave the Dolphin Compact HomeBase connected to its power source at all times, so
that it is always ready to use.
Pin Configuration
HomeBase /Host Port (DCE) IBM AT DB9 (DTE) IBM XT DB25 (DTE) Modem DB25 (DCE)
2 (RD) 2 3 2
3 (TD) 3 2 3
5 (SG) 5 7 7
4 (DTR) 4 20 6
6 (DSR) 6 6 20
7 (RTS) 7 4 5
8 (CTS) 8 5 4
- User’s Guide 1
- Disclaimer 2
- Trademarks 2
- Table of Contents 3
- Chapter 7 - Troubleshooting 5
- Chapter 8 - Dolphin HomeBase 5
- Chapter 9 - Compact HomeBase 6
- Introduction 9
- Required Safety Labels 10
- Locations 10
- Canadian Notice 11
- Batteries 12
- Getting Started 13
- Dolphin 7200 RS-232 14
- Dolphin 7200 Models 15
- Step 1. Checking Your Package 16
- Step 2. Charging the Battery 16
- Inserting the Battery Pack 17
- Removing the Battery Pack 17
- Turning the Dolphin On 17
- Turning the Dolphin Off 18
- Dolphin 7200 Basics 19
- Using the Alphanumeric Keypad 20
- Using the Numeric Keypad 22
- Display Symbols 23
- Back Panel Features 24
- Internal NiMH Backup Battery 26
- Guidelines 26
- NiMH Battery Pack 26
- Servicing the Battery Pack 27
- Charging the Battery Pack 27
- Storing Battery Packs 27
- Sending and Receiving Data 30
- Supported Symbologies 31
- Reading Barcodes 32
- Capturing Images 33
- Lighting Conditions 33
- Dolphin 7200 2D Demo Software 33
- Dolphin Demo Main Screen 34
- F1 - Decoding Demo 34
- F2 - Imaging Demo 35
- F3 - I.Q. Imaging Demo 35
- Hand Held Products 36
- 7520 E. Independence Blvd 36
- Charlotte, NC 28227 36
- Installation 37
- Dolphin Utilities 39
- ROM Image 42
- Sample Applications 43
- Building the Samples 44
- Sending a File to the Dolphin 45
- Sending Files to the Dolphin 46
- Dolphin EVS Engine 47
- for repair 48
- Troubleshooting 49
- Dolphin HomeBase 51
- Front Panel 52
- Back Panel 53
- Side Panels 54
- Charging a Dolphin Terminal 55
- Deep-Cycling the Battery 56
- Communications 56
- Connecting the Cables 57
- Setting the Baud Rate 58
- Version Number 58
- Baud Rate Selection 58
- Programming Commands 59
- Baud Rate per Value of n 59
- Address Assignment 60
- Device Selection 61
- Compact HomeBase 63
- Bottom Panel 66
- Powering the Dolphin Terminal 66
- Deep-Cycling Batteries 67
- Wall Mounting: 68
- Setting Up for Communications 70
- Dolphin Vehicle Base 73
- Selecting the Baud Rate 74
- Side Panel Features 75
- Battery Temperatures 76
- Cables for the VehicleBase 77
- Dolphin MultiCharger 79
- Top Panel 80
- Declaration of Conformity 83
- Customer Support 85
- Technical Assistance 86
- Limited Warranty 87
- Technical Specifications 89
- Bar Code Samples 93
- Decoding Demo Menu Layout 95
- 2D Decoding Demo Screen Shots 96
- Decode Mode 97
- To set the Mode, Press: 97
- Decoding Options 97
- DISABLED!!!! 98
- ALD Window 99
- IQ Imaging Test Target 101
- GS-DOS Commands 103
- Syntax: VOL [drive:] 108
- Declarations of Conformity 109
- Signature On File 110
- 89/336/EEC EMC Directive 111
- Hand Held Products, Inc 114
Related products and manuals for Accessories communication Hand-held-products Dolphin 7200
(102 pages)© 2020, manymanuals.com. All rights reserved. | 6.000 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals